st0ner
I need help pls..i just build computer,
M2R32 MVP MOBO
AMD ATHLON 64 X2 6000+
ATI RADEON 3870
CORSAIR 4GB RAM
WD 500GB HD
20X DVD DRIVE
My question is why my computer cme up with no boot screen. video card, cpu fan, psu, hd and mobo are running fine, but when i connect
the monitor to video card, no boot screen came up. just black.
I did cmos/bios reset for numerous time.
for a note, i placed the ram on slot a2 and b2, it this effect this cause? thankyou for your reply
M2R32 MVP MOBO
AMD ATHLON 64 X2 6000+
ATI RADEON 3870
CORSAIR 4GB RAM
WD 500GB HD
20X DVD DRIVE
My question is why my computer cme up with no boot screen. video card, cpu fan, psu, hd and mobo are running fine, but when i connect
the monitor to video card, no boot screen came up. just black.
I did cmos/bios reset for numerous time.
for a note, i placed the ram on slot a2 and b2, it this effect this cause? thankyou for your reply
Participate on our website and join the conversation
This topic is archived. New comments cannot be posted and votes cannot be cast.
Responses to this topic
danleff
Any beep codes on boot try?
Make sure that the video card is properly seated.
Try memory in slots A1 and B1 and that they are seated properly.
You did not mention what exact memory that you are using.
What exact make and model power supply are you using? And, you have the main power connector attached as well as the 4 pin CPU fan connector also attached?
The onboard LED is green on boot?
Make sure that the video card is properly seated.
Try memory in slots A1 and B1 and that they are seated properly.
You did not mention what exact memory that you are using.
What exact make and model power supply are you using? And, you have the main power connector attached as well as the 4 pin CPU fan connector also attached?
The onboard LED is green on boot?
st0ner
OP
the mobo didnt have speaker on it, video card fans running properly,
im using CORSAIR 4GB(2 x 2GB) DDR2 800 (PC2 6400)
psu cooler master 750w
onboard led was on when i turned the power on,
4 pin and 24 pin connectors are connected to the mobo,
mobo lights is on, but still no boot screen on monitor??
thank you for your reply
im using CORSAIR 4GB(2 x 2GB) DDR2 800 (PC2 6400)
psu cooler master 750w
onboard led was on when i turned the power on,
4 pin and 24 pin connectors are connected to the mobo,
mobo lights is on, but still no boot screen on monitor??
thank you for your reply
danleff
OK, having a system speaker on the case would help if there were any bios beep codes on boot.
Make sure that the monitor is powered on before hitting the system power switch.
Did you try the suggested memory placement? Make sure that the memory is seated properly.
The video card has a 6-pin PCI Express power connector to the power supply connected?
If so, I would try re-seating the video card, making sure that you use the blue primary PCI-E x16 slot.
and..you are sure that there are no possible shorts between the motherboard and case?
Finally, make sure that the CMOS jumper is in the normal position and not in the reset position. I have seen the factory set it to reset by mistake.
Make sure that the monitor is powered on before hitting the system power switch.
Did you try the suggested memory placement? Make sure that the memory is seated properly.
The video card has a 6-pin PCI Express power connector to the power supply connected?
If so, I would try re-seating the video card, making sure that you use the blue primary PCI-E x16 slot.
and..you are sure that there are no possible shorts between the motherboard and case?
Finally, make sure that the CMOS jumper is in the normal position and not in the reset position. I have seen the factory set it to reset by mistake.
st0ner
OP
monitor is on, memory is seated properly
video card on blue primary pci-e x16
Ok so I disconnected everything except:
MB
Processor
1 stick RAM
video card
usb keyboard
I took everything out of the case and put mb on cardboard.
cmos jumper on normal position, but still no boot screen
??? thanks 4 your reply
video card on blue primary pci-e x16
Ok so I disconnected everything except:
MB
Processor
1 stick RAM
video card
usb keyboard
I took everything out of the case and put mb on cardboard.
cmos jumper on normal position, but still no boot screen
??? thanks 4 your reply
danleff
Try this;
Do a power supply reset by unplugging the power cord, then push the power button in and hold for 10 seconds. Re-plug the power cord, and try to power on the computer.
Lets see if the Asus site allows links to their troubleshooting section.
Trobleshooting Matrix
There is an error on their link to the section on led lit-->no display-->fan spinning-->no abnormal beep sound.....
The link for your situation is the row above, as if you had abnormal beep sounds. But, of course, you have no system speaker attached, so read both.
If this fails;
Do you have a PS/2 keyboard to try?
...and you are sure that the processor is supported?
Athlon 64 X2 6000+ (CZ),2MB,rev.F3,125W,SocketAM2 is supported for the motherboard. Note the CZ version of the chip. Is this what you have?
The problem here is that in the absence of beep codes (which may be helpful) we are taking shots in the dark.
Do a power supply reset by unplugging the power cord, then push the power button in and hold for 10 seconds. Re-plug the power cord, and try to power on the computer.
Lets see if the Asus site allows links to their troubleshooting section.
Trobleshooting Matrix
There is an error on their link to the section on led lit-->no display-->fan spinning-->no abnormal beep sound.....
The link for your situation is the row above, as if you had abnormal beep sounds. But, of course, you have no system speaker attached, so read both.
If this fails;
Do you have a PS/2 keyboard to try?
...and you are sure that the processor is supported?
Athlon 64 X2 6000+ (CZ),2MB,rev.F3,125W,SocketAM2 is supported for the motherboard. Note the CZ version of the chip. Is this what you have?
The problem here is that in the absence of beep codes (which may be helpful) we are taking shots in the dark.
