Power DVD Problem in Win2000
This is a discussion about Power DVD Problem in Win2000 in the Windows Software category; I run PowerDVD version 2. 55 in windows 2000 and although it runs normally when i insert a dvd in my dvd drive an error message appears that says Cannot find wnaspi32. dll and the DVD won't play. Does anyone know what to do?.
I run PowerDVD version 2.55 in windows 2000 and although it runs normally when i insert a dvd in my dvd drive an error message appears that says "Cannot find wnaspi32.dll" and the DVD won't play.Does anyone know what to do?
Participate in our website and join the conversation
This subject has been archived. New comments and votes cannot be submitted.
Jul 13
Jul 14
0
4 minutes
Responses to this topic
What is your system setup? I can't help you if I don't know what your system is.
------------------
Supermicro P6DBE Rev 3.0 Motherboard
Dual Intel Pentium III 850
512 MEGS of ECC RAM
Sound Blaster Live!
Adaptec 29160 SCSI Card
GeForce 2 GTS 64MB
IBM DMVS18N Ultra 160 Hard Drive
Western Digital 20.5GB Hard Drive
Razer Boom Slang 2000 (USB)
Roland Sound Canvis SC-55
3COM 3CR990-TX-97 with 3XP Processor 10/100 PCI Network Interface Card
Plextor Plexwriter 12/4/32
Pioneer 10X DVD-ROM
Sony GDM-F500R Monitor
------------------
Supermicro P6DBE Rev 3.0 Motherboard
Dual Intel Pentium III 850
512 MEGS of ECC RAM
Sound Blaster Live!
Adaptec 29160 SCSI Card
GeForce 2 GTS 64MB
IBM DMVS18N Ultra 160 Hard Drive
Western Digital 20.5GB Hard Drive
Razer Boom Slang 2000 (USB)
Roland Sound Canvis SC-55
3COM 3CR990-TX-97 with 3XP Processor 10/100 PCI Network Interface Card
Plextor Plexwriter 12/4/32
Pioneer 10X DVD-ROM
Sony GDM-F500R Monitor
goto www.adaptec.com and install the UDFReader drivers, and any other stuff. ASPI (Advanced SCSI Programming Interface) is used to make reading removeable media (not always scsi hardware) easy to use in programs. Powerdvd can't find it. Either copy and expand it from win2000 CD, or download scsi drivers from adaptec (if your drive is SCSI). Most likley its gone missing
Check powerdvd is using the correct drive, and its being registered properly and DMA is on/off (on via boards when its unchecked its on! and vice-versa), thats device manager/dvd to find DMA.
Check powerdvd is using the correct drive, and its being registered properly and DMA is on/off (on via boards when its unchecked its on! and vice-versa), thats device manager/dvd to find DMA.
OP
Quote:Originally posted by andysk:
I run PowerDVD version 2.55 in windows 2000 and although it runs normally when i insert a dvd in my dvd drive an error message appears that says "Cannot find wnaspi32.dll" and the DVD won't play.Does anyone know what to do?
My system has:
Pentium 3 at 600/133mhz
256mb ram
voodoo 3 3000 with tvout
dvd pioneer 104s with the region free firmware
soundblaster live
I run PowerDVD version 2.55 in windows 2000 and although it runs normally when i insert a dvd in my dvd drive an error message appears that says "Cannot find wnaspi32.dll" and the DVD won't play.Does anyone know what to do?
My system has:
Pentium 3 at 600/133mhz
256mb ram
voodoo 3 3000 with tvout
dvd pioneer 104s with the region free firmware
soundblaster live
I had the same problem. Never found out why I didn't have that file though. I just copied it from the DVD-ripper called Decc. (I think it is spelled like that)
Quote:Originally posted by andysk:
Quote:Originally posted by andysk:
I run PowerDVD version 2.55 in windows 2000 and although it runs normally when i insert a dvd in my dvd drive an error message appears that says "Cannot find wnaspi32.dll" and the DVD won't play.Does anyone know what to do?
My system has:
Pentium 3 at 600/133mhz
256mb ram
voodoo 3 3000 with tvout
dvd pioneer 104s with the region free firmware
soundblaster live
You have the same DVD that I have (except mine is 114). They did do a firmware update a few months back. I was verion 1.02 before I went 2.03 (I didn't know about the updates till Diablo II cameout, because it couldn't read the CD). The firmware update can be found at http://www.pioneerusa.com/tec.html#drivers When you try to update your firmware, remember that it will take more than one minute and don't go crazy if it looks like it froze. I thought the samething and was about to press reset when common sense kicked in I am also using PowerDVD 2.55 that came with Hercules Prophet II 64MB (It came with 2.5 and I updated to 2.55). After you update your firmware uninstall PowerDVD( including the directory if the uninstall couldn't delete the directory). Also make sure DMA is enabled for your DVD drive (Device Manager IDE ATA/ATAPI controllers). IF this doesn't help, just keep replying here
------------------
Supermicro P6DBE Rev 3.0 Motherboard
Dual Intel Pentium III 850
512 MEGS of ECC RAM
Sound Blaster Live!
Adaptec 29160 SCSI Card
GeForce 2 GTS 64MB
IBM DMVS18N Ultra 160 Hard Drive
Western Digital 20.5GB Hard Drive
Razer Boom Slang 2000 (USB)
Roland Sound Canvis SC-55
3COM 3CR990-TX-97 with 3XP Processor 10/100 PCI Network Interface Card
Plextor Plexwriter 12/4/32
Pioneer 10X DVD-ROM
Sony GDM-F500R Monitor
Quote:Originally posted by andysk:
I run PowerDVD version 2.55 in windows 2000 and although it runs normally when i insert a dvd in my dvd drive an error message appears that says "Cannot find wnaspi32.dll" and the DVD won't play.Does anyone know what to do?
My system has:
Pentium 3 at 600/133mhz
256mb ram
voodoo 3 3000 with tvout
dvd pioneer 104s with the region free firmware
soundblaster live
You have the same DVD that I have (except mine is 114). They did do a firmware update a few months back. I was verion 1.02 before I went 2.03 (I didn't know about the updates till Diablo II cameout, because it couldn't read the CD). The firmware update can be found at http://www.pioneerusa.com/tec.html#drivers When you try to update your firmware, remember that it will take more than one minute and don't go crazy if it looks like it froze. I thought the samething and was about to press reset when common sense kicked in I am also using PowerDVD 2.55 that came with Hercules Prophet II 64MB (It came with 2.5 and I updated to 2.55). After you update your firmware uninstall PowerDVD( including the directory if the uninstall couldn't delete the directory). Also make sure DMA is enabled for your DVD drive (Device Manager IDE ATA/ATAPI controllers). IF this doesn't help, just keep replying here
------------------
Supermicro P6DBE Rev 3.0 Motherboard
Dual Intel Pentium III 850
512 MEGS of ECC RAM
Sound Blaster Live!
Adaptec 29160 SCSI Card
GeForce 2 GTS 64MB
IBM DMVS18N Ultra 160 Hard Drive
Western Digital 20.5GB Hard Drive
Razer Boom Slang 2000 (USB)
Roland Sound Canvis SC-55
3COM 3CR990-TX-97 with 3XP Processor 10/100 PCI Network Interface Card
Plextor Plexwriter 12/4/32
Pioneer 10X DVD-ROM
Sony GDM-F500R Monitor
